# Tuning Guide¶

This guide helps you optimize a Cilium installation for optimal performance.

## eBPF Host-Routing¶

Even when network routing is performed by Cilium using eBPF, by default network packets still traverse some parts of the regular network stack of the node. This ensures that all packets still traverse through all of the iptables hooks in case you depend on them. However, they add significant overhead. For exact numbers from our test environment, see TCP Throughput (TCP_STREAM) and compare the results for “Cilium” and “Cilium (legacy host-routing)”.

We introduced eBPF-based host-routing in Cilium 1.9 to fully bypass iptables and the upper host stack, and to achieve a faster network namespace switch compared to regular veth device operation. This option is automatically enabled if your kernel supports it. To validate whether your installation is running with eBPF host-routing, run cilium status in any of the Cilium pods and look for the line reporting the status for “Host Routing” which should state “BPF”.

Requirements:

• Kernel >= 5.10
• Direct-routing configuration or tunneling
• eBPF-based kube-proxy replacement

## Bypass iptables Connection Tracking¶

For the case when eBPF Host-Routing cannot be used and thus network packets still need to traverse the regular network stack in the host namespace, iptables can add a significant cost. This traversal cost can be minimized by disabling the connection tracking requirement for all Pod traffic, thus bypassing the iptables connection tracker.

Requirements:

• Kernel >= 4.19.57, >= 5.1.16, >= 5.2
• Direct-routing configuration
• eBPF-based kube-proxy replacement

To enable the iptables connection-tracking bypass:

cilium install --config install-no-conntrack-iptables-rules=true

helm install cilium cilium/cilium --version 1.10.4 \
--namespace kube-system \
--set installNoConntrackIptablesRules=true \
--set kubeProxyReplacement=strict


## Hubble¶

Running with Hubble observability enabled can come at the expense of performance. The overhead of Hubble is somewhere between 1-15% depending on your network traffic patterns and Hubble aggregation settings.

In order to optimize for maximum performance, Hubble can be disabled:

cilium hubble disable

helm install cilium cilium/cilium --version 1.10.4 \
--namespace kube-system \
--set hubble.enabled=false


## MTU¶

The maximum transfer unit (MTU) can have a significant impact on the network throughput of a configuration. Cilium will automatically detect the MTU of the underlying network devices. Therefore, if your system is configured to use jumbo frames, Cilium will automatically make use of it.

To benefit from this, make sure that your system is configured to use jumbo frames if your network allows for it.

## Bandwidth Manager¶

Cilium’s Bandwidth Manager is responsible for managing network traffic more efficiently with the goal of improving overall application latency and throughput.

Aside from natively supporting Kubernetes Pod bandwidth annotations, the Bandwidth Manager, first introduced in Cilium 1.9, is also setting up Fair Queue (FQ) queueing disciplines to support TCP stack pacing (e.g. from EDT/BBR) on all external-facing network devices as well as setting optimal server-grade sysctl settings for the networking stack.

Requirements:

• Kernel >= 5.1
• Direct-routing configuration or tunneling
• eBPF-based kube-proxy replacement

To enable the Bandwidth Manager:

helm install cilium cilium/cilium --version 1.10.4 \
--namespace kube-system \
--set bandwidthManager=true \
--set kubeProxyReplacement=strict


To validate whether your installation is running with Bandwidth Manager, run cilium status in any of the Cilium pods and look for the line reporting the status for “BandwidthManager” which should state “EDT with BPF”.

## XDP Acceleration¶

Cilium has built-in support for accelerating NodePort, LoadBalancer services and services with externalIPs for the case where the arriving request needs to be pushed back out of the node when the backend is located on a remote node.

In that case, the network packets do not need to be pushed all the way to the upper networking stack, but with the help of XDP, Cilium is able to process those requests right out of the network driver layer. This helps to reduce latency and scale-out of services given a single node’s forwarding capacity is dramatically increased. The kube-proxy replacement at the XDP layer is available from Cilium 1.8.

Requirements:

• Kernel >= 4.19.57, >= 5.1.16, >= 5.2
• Native XDP supported driver, check our driver list
• Direct-routing configuration
• eBPF-based kube-proxy replacement

To enable the XDP Acceleration, check out our getting started guide which also contains instructions for setting it up on public cloud providers.

To validate whether your installation is running with XDP Acceleration, run cilium status in any of the Cilium pods and look for the line reporting the status for “XDP Acceleration” which should say “Native”.

## eBPF Map Sizing¶

All eBPF maps are created with upper capacity limits. Insertion beyond the limit would fail or constrain the scalability of the datapath. Cilium is using auto-derived defaults based on the given ratio of the total system memory.

However, the upper capacity limits used by the Cilium agent can be overridden for advanced users. Please refer to the eBPF Maps guide.

## Linux Kernel¶

In general, we highly recommend using the most recent LTS stable kernel (such as >= 5.10) provided by the kernel community or by a downstream distribution of your choice. The newer the kernel, the more likely it is that various datapath optimizations can be used.

In our Cilium release blogs, we also regularly highlight some of the eBPF based kernel work we conduct which implicitly helps Cilium’s datapath performance such as replacing retpolines with direct jumps in the eBPF JIT.

Moreover, the kernel allows to configure several options which will help maximize network performance.

### CONFIG_PREEMPT_NONE¶

Run a kernel version with CONFIG_PREEMPT_NONE=y set. Some Linux distributions offer kernel images with this option set or you can re-compile the Linux kernel. CONFIG_PREEMPT_NONE=y is the recommended setting for server workloads.

## Further Considerations¶

Various additional settings that we recommend help to tune the system for specific workloads and to reduce jitter:

### tuned network-* profiles¶

The tuned project offers various profiles to optimize for deterministic performance at the cost of increased power consumption, that is, network-latency and network-throughput, for example. To enable the former, run:

tuned-adm profile network-latency


### Set CPU governor to performance¶

The CPU scaling up and down can impact latency tests and lead to sub-optimal performance. To achieve maximum consistent performance. Set the CPU governor to performance:

for CPU in /sys/devices/system/cpu/cpu*/cpufreq/scaling_governor; do
echo performance > \$CPU
done


### Stop irqbalance and pin the NIC interrupts to specific CPUs¶

In case you are running irqbalance, consider disabling it as it might migrate the NIC’s IRQ handling among CPUs and can therefore cause non-deterministic performance:

killall irqbalance


We highly recommend to pin the NIC interrupts to specific CPUs in order to allow for maximum workload isolation!

See this script for details and initial pointers on how to achieve this. Note that pinning the queues can potentially vary in setup between different drivers.

We generally also recommend to check various documentation and performance tuning guides from NIC vendors on this matter such as from Mellanox, Intel or others for more information.